CAMERA GUARD FORGOT PASSWORD HOW TO
CAMERA GUARD FORGOT PASSWORD MANUAL
CAMERA GUARD FORGOT PASSWORD PASSWORD

Make sure that the camera power switch is in the “ON” position and not in the “OFF”.įirst we recommend that you take a few minutes to watch the video to quickly learn how to start the WiFi camera. Please gently remove the protective films in the front of the camera to get the best performance, especially the protective films attached to the PIR sensors will seriously reduce the motion detection ability and even cause no capture.If this is the case, please contact our customer service to send the camera back for repair. If the camera continues to show issues, then there is probably an electronic component issue.If the camera continues to take images when there is no subject in them, try placing the camera in an inside environment and aiming at a location where there is no motion.Try moving the camera to an area that does not have any of these issues or try changing the sensor level on the menu settings.Setting a camera up over water is also a potential cause for this issue. These “False Triggers” are the result of placing the camera in an environment where there is motion associated with tree branches creating motion in front of the camera or an area where there is high heat in the foreground and any motion from wind could set off the camera. Run motion detection test by “Motion Test” menu option to check whether the motion sensor does work.Ī camera has what is known as a “false trigger” if the PIR sensor thinks that there is motion and heat in front of the camera lens when there is no subject in the image.If you are using rechargeable batteries, it would not take nighttime pictures or videos due to the low battery voltage (generally nominal 1.2V and drops down quickly). IMPORTANT: Check the batteries to make sure their power level is sufficient.so please re-format SD card and try again. Or if the SD card has been used for a long time, the SD card might be in unstable status and not able to accept data writing into, in this case, the camera behaves as not triggering and not taking pictures. In some cases, other devices may change the formatting of the SD card so that it will not work properly with the camera. IMPORTANT: If you have used an SD card in another device before inserting it in your camera, you might want to try formatting the card using the “Format SD Card” menu option in SET mode (make sure you have backed up any important files first, as formatting will erase all previous files).We recommend SD/SDHC/SHXC Class10 brand memory card, such as SanDisk, Kingston, Toshiba, Samsung, etc.

Make sure that you are using a good quality SD card in your camera.

The default option is “Loop Recording” disabled, the camera will stop taking images when the SD card reaches capacity.

Please make sure that the SD card doesn’t reach capacity.

Check the “Detection Delay” in menu settings, which is the delay between current capture and next capture, set “Detection Delay” to a lower value if you want more captures.

Make sure the camera had been powered up for more than 60 seconds to ensure the PIR sensors have been fully activated.

Make sure that the camera power switch is in the “ON” position and not in the “OFF” or “SET”.

CAMERA GUARD FORGOT PASSWORD MANUAL

Please give a mandatory reset to the cameraġ) If your outdoor camera happens to have no reset button,please download the IP camera Reset tool and manual for this link Ģ)Please well note,this method only applied for your camera and your local PC in the same router.Please gently remove the protective films in the front of the camera to get the best performance, especially the protective films attached to the PIR sensors will seriously reduce the motion detection ability and even cause no capture.

CAMERA GUARD FORGOT PASSWORD PASSWORD

If you forget your login user name and password, recommend you reset your camera as below,Ģ) Find toothpick or something pointy to press the reset button (default position is on the bottom of the camera or nearby the antenna) about 15 seconds till the camera reboot, then release it ģ) After reset, it will restore to the default factory setting, the user is admin, password is adminĢ) Press and hold the reset button (it is on the end of the reset line) for 15 seconds, then release.ģ) After reset, it will restore to the default setting, the user is admin, password is adminįor part of the latest models with UID number cameras: Forgot user name or password of camera, what should i do next?

Camera guard forgot password